1. F00ZC01361 Injector Valve Set Technical Support
1.1. F00ZC01361 Injector Valve Set Installation Precautions
(1) Clean the injector valve set in an ultrasonic cleaner for 3-5 minutes before installation, so as to make the stains, dust, rust-proof oil oxides, paraffin base, naphthenic base, intermediate base, salt, lead naphthenate, zinc naphthenate, sodium petroleum sulfonate, barium petroleum sulfonate, calcium petroleum sulfonate, tallow diamine trioleate, rosinamine on the surface of the injector valve set fall off.
(2)Use compressed air to clean the cleaning fluid attached to the surface of the injector valve set after cleaning, and clean it up to the standard of use.
(3)When installing the steel ball and ball seat, pay attention to the steel ball should close tightly to the oil return hole at the top of the valve cap, as shown below:
Pic No.1
① When installing the valve stem, make sure that the valve stem and the bonnet must ensure that the valve stem can move smoothly in it, as shown below:
Pic No.2
② When installing the injector valve set, the oil inlet position should be 180°between the oil inlet position of the injector body.
- If the injector steel ball and the ball seat are not installed in accordance with the standard, it may cause serious damage to the injector valve set.
1.2. F00ZC01361 Injector Valve Set Replacement Conditions
(1) Valve Cap
Under the microscope, magnify 20 times to check that the oil inlet hole of the valve cap and the oil return hole of the bonnet are not worn, grooved, scratched, damaged, rusted or dented.
|
No.
|
1 |
2 |
3 |
| Image |
 |
 |
|
|
Description
|
Injector valve set oil inlet hole location |
Injector valve set oil return hole location |
The oil inlet and oil return holes of the injector valve set are free of wear, grooves, scratches, damage, rust, dents, which do not need to be replaced |
|
No.
|
4 |
5 |
6
|
|
Image
|
 |
 |
 |
|
Description
|
The injector valve set oil hole is recessed and needs to be replaced |
The injector valve set oil hole is worn and needs to be replaced |
The injector valve set oil hole is punched and needs to be replaced |
- The wear of the top oil return hole causes the oil return to be too large and the leaking injector cannot inject oil.
- The oil inlet hole on the side is blocked, causing the injector to fail to establish the pressure chamber and the injector cannot work normally
- Wear of the oil chamber of the valve cap will cause fuel injector failure. In severe cases, the fuel injector will not work properly.
(2) Valve Stem
Magnify 20 times under a microscope to check whether the valve stem is worn, the surface is not smooth, discolored, or rusty.
|
No.
|
1 |
2 |
3 |
| Image |
 |
 |
|
|
Description
|
The valve stem is worn out and needs to be replaced |
The valve stem surface is not smooth and colorless, and it needs to be replaced |
The valve stem is rusty and needs to be replaced |
- The excessive clearance between the valve stem wear, housing and the valve cap will causes injector
- The valve stem lag will cause the injector to start the solenoid to start, and the oil needle can not return quickly after the nozzle is opened.
- Check the injector components before replacing the injector valve set according following the injector service manual to avoid further damage to the injector valve set after replacement.
All content on this passage “F00ZC01361 Injector Valve Set Encyclopedia” is sourced from and belongs to Shenzhen Shumatt Technology Co., Ltd. www.injectorpart.com has been authorized to use this content. Any reproduction, distribution, or public display of this material must clearly acknowledge Shenzhen Shumatt Technology Co., Ltd. as the source. Unauthorized use or failure to comply with these conditions will constitute a violation of the “Copyright Law of the People’s Republic of China” and other relevant international laws and regulations.
